Sorry uploaded the wrong File, here is the correct one

I put it to data folder but when I wanted to add it to chart I got error message

Try this .dll, should work without an issue. I just copied it and tested it on a second laptop. Works fine for me. Anyone else having troubles with the study other than lemons?

I get error 126. Regards Outlander

Weird, I recompiled it on a different maschine and set it to release mode, tested it on my girlfriends laptop with a clean updated install of Sierrachart. Works fine again for me, are you sure you put it into the Data Folder?

Try this file, let me know if it works


EDIT:

You should get the error message when you delete a .dll while its saved onto a chart within a chartbook, because then sierra cant find the file.
1) Delete the old .dll
2) Remove the old study from your studylist on the chart you loaded it onto
3) Copy the new .dll into C:\SierraChart\Data or wherever your data folder is for sierra
4) Load it into the chart by adding it from the studies window.
5) Done

This error means the DLL (dynamic link library) file that contains the Advanced Custom Study or Studies that you are using could not be found. You will need to obtain the specified DLL file and save it to your Sierra Chart Data Files Folder. Please see Step #1 above for instructions.
When you save the DLL file to the Sierra Chart Data Files Folder, make certain it has a DLL file extension. Software which blocks malicious software such as antivirus software, can also potentially block the use of a downloaded DLL file and this can also cause this same error message.
If you are unable to resolve this error, you will need to remove the Advanced Custom Study or Studies from your chart or charts to prevent the error from appearing again. To do this, go to one of your charts, select Analysis >> Studies to view the Chart Studies window. In the Studies to Graph section, select Custom DLL Study and press Remove to remove the study. Remove all of the Custom DLL Study studies from the list and press OK to save the settings. You will need to do this for each chart that has a Custom DLL Study study which is causing the error.

This is very odd, just let another friend test it and he says it works fine (he had to update sierrachart though).

How to Use an Advanced Custom Study and Study Collections - Sierra Chart

Basically means you are messing up with putting the file in the correct folder.



Just in case i am attaching the source code for you so you can compile it yourself.

Not sure whats going on Outlander, Update Sierrachart, and compile the sourcecode and you should be good to go.

Not sure whats going on Outlander, Update Sierrachart, and compile the sourcecode and you should be good to go.

Sorry for all the trouble. The problem must be in my end. I have only used the spreadsheet and don't know how to make own studys or how to compile. Regards Outlander

Finally got it to work

I was also unable to add the DLL (grayed out here too), but after compiling the Source.cpp file I was able to add the study.

I've attached the DLL resulting from compiling the source file.

Hope this helps

Btw: I didn't really mess around much with the study once I added it, but it appears to be in order. Something mildly interesting is that the original DLL was 42kb whereas my compiled version is only 20kb.

How is everybody doing here is this thread? There was a lot of encouraging results trading FlexRenko/UniRenko pull backs from Hapster, Cory, Outlander. I'm wondering if it's still profitable months later?

Regards Outlander

How do you us flexrenko in your trading ?
- entry signal ?
- exit signal ?

greeting read the topic .. I have mostly sierra chart and use ordinary range chart ... I have the options of flex Renko but can not get the graph to look at you, in what is my problem? thanks

The settings for the TF chart is 19/15/16. I use this setting for most of my charts. FDAX uses 22/7/14.
Regards Outlander: crazy_pilot:

like being on the graph ... and setting ... it is not the same as your, why

c

lemons ,outlander thanks...

Here's the way it seemed to me somehow 12-6-3 TF ... outlander your graphs are a little confused ... I do not understand the particular signals for input output ...?

CL at the European morning. I have changed the FlexRenko settings to 4-2-2 and it seems to me that they now are more correct. The trades are CLR trades in automode. It uses stop orders for entry.
Regards Outlander

whether in standard studies sierra such indicators? how to put them? to test

I was wondering how to make a cloud between MA,, that's what I get can not get on with my setup

Regards Outlander